Dampers

Lock Top Damper

The Lock-Top Damper seals out pests and weather problems with its quality built, rigid construction. It is a low cost solution to replace throat dampers to help prevent heat and air conditioning loss from your home.

Damper includes 30' cable, adhesive, and mounting hardware. Lifetime warranty. Note: Do not use Lock-Top dampers with gas logs.

Click for details...

Lock Top II Damper

The Lock-Top II damper has a specially designed chimney cap. It comes fully assembled and ready to install directly to the flue tile.

Includes 30' stainless steel cable, adhesive, and mounting hardware. Lifetime warranty. Note: Do not use Lock-Top Dampers with gas logs.

Click for details...

Energy Top Damper

The Energy Top Damper is a low profile top-mounted damper that also serves as a chimney cap. When closed, it is virtually invisible from the ground. It provides a tight, gasketed fit that seals in heat and seals out weather, insects, birds and animals. A slight pull on the chain releases the spring-loaded top into the open position. When open, this damper is least obstructive to exiting smoke.

Includes 30', cut to fit cable, fireplace bracket, cool-touch spring handle, mounting adhesive and hardware. Lifetime warranty. Do not use on chimneys venting gas logs.

Click for details...

Energy Top Plus Cap

The Energy Top plus cap is about 90% more efficient than traditional dampers. Install at the top of the chimney and completely seal the flue shut with a flexible silicone rubber gasket when the fireplace is not is use. Energy Top dampers with caps prevent heat from escaping up the chimney and chilly drafts from entering the home. The Energy Top plus cap also serves as a chimney cap/spark arrestor.

Includes 30', cut to fit cable, fireplace bracket, cool-touch spring handle, mounting adhesive and hardware. Lifetime warranty. Do not use on chimneys venting gas logs.

Click for details...

Lyemance Original Top Sealing Damper

This swing door damper is made of cast aluminum and comes with a 32' stainless steel cable. The cable is connected to the spring-loaded Power Level Damper.

Includes mounting hardware and sealant. Note: Do not use Lyemance dampers with gas logs.

• Easily mounts atop flue tile
• Lifetime warranty
• Silicone rubber seals tight.

Click for details...

Sealtight Damper

This is a great option if you don't want a cap visible on your chimney. It provides a tight gasketed fit to seal out weather, insects, birds and animals while keeping heat in. Or, if you prefer a cap, it can also be installed beneath an HY‑C chimney cap.

Includes 30', cut to fit cable, fireplace bracket, cool-touch spring handle, mounting adhesive and hardware. Lifetime warranty. Do not use on chimneys venting gas logs.

Click for details...

Round Stainless Steel Chimney Damper Kit

This round chimney damper is constructed from quality 316Ti stainless steel. Built to withstand repeated chimney fires, it will not melt like other dampers.

Installation is simple: the damper is recessed approximately 6 inches below the flue's termination point. Ideal for restoration projects where an exposed damper would be objectionable. A rain cover of your choice can be installed over it without fear of a freezing or sticking damper.

This is an excellent replacement for worn-out, warped and defective factory-built zero clearance dampers. 30' cable included.

Replacement Hardware Pack for Dampers

Contains: Chain assembly, bracket, nail anchors, adhesive and allen wrench.

Replacement Cable for Dampers

50 foot cable.

CHIM-A-LATOR®

The CHIM-A-LATOR® line of Chimney Cap Dampers easily mount to the top of a masonry or clay tile chimney top with a simple screwdriver. 100% stainless steel. Proven more reliable than bottom mount cast iron dampers, easier to operate, and more efficient to save your energy dollars from being wasted up the chimney. Six damper handle settings allow you to adjust the damper opening for precise draft control.

Click for details...

CHIM-A-LATOR® Flue Extension

You may need a flue extension to mount your CHIM-A-LATOR® if there is no existing flue tile extending from the chimney top or the flue tile is too short. The extension pieces are 4 inches tall and tapcon screws are included. CHIM-A-LATOR® easily bolts to the flue extension.

Chimney Balloon

The Chimney Balloon (AKA The Chimney Pillow) is an inflatable fireplace draft stopper. Inflate into place in the fireplace flue just above the damper. It makes an airtight seal that blocks outside air and chimney odor from entering your home. The balloon is designed with a low heat melting point that will release the balloon if a fire is accidentally ignited.

Chimney Balloon FAQ
Chimney Balloon Installation Video

Handle/Valve Extender Kit

for use with the Chimney Balloon®

The HEK Handgrip/Valve Extender Kit is a way to get a further reach with your Chimney Balloon®. The HEK allows you many extra inches of reach and the valve handle is near the valve mouth. This is highly recommended if you have a damper that is high in the chimney or if you plan on installing your Chimney Balloon high in the chimney.

Rule of Thumb: If you can not easily touch the area you measured for your Chimney Balloon with your hand...you should buy an HEK Extender. It will make installation of the Chimney Balloon much easier.

Damper Sealing Kit

This Damper Sealing Kit is designed to seal off your damper once you have installed a chimney liner which has passed through the damper and is connected directly to the top of the insert. Intended to be used when a chimney liner is being installed; attaches to existing damper frame.

Includes two galvanized metal sections which adjust to fit around the chimney liner. Seals off dampers up to 48 inches wide. Also includes insulation and all hardware required to complete the job. Flex connector/chimney liner not included. Click here for damper sealing kit instructions.