DuraVent Dura Tech Class A Pipe 5" to 8"

From$110.11

DuraTech Class A Chimney Pipe is a double wall insulated chimney pipe ideal for venting residential heating appliances such as wood stoves, fireplaces, furnaces, boilers, water heaters and zero clearance factory built fireplaces. It is constructed with a 430 Stainless Steel inner wall wrapped with 1" thick ThermalTech insulation encased in a... Read More

From$457.89

The DuraTech Insulated Class A Tee and Tee Cap is used for through the wall installations to turn the horizontal pipe coming through the wall vertically for the exterior chimney stack. The Insulated Tee comes with a removable clean out cap to make cleaning and inspections a breeze. The Tee... Read More

From$175.32

The DuraTech Class A Standard Flashing is used to seal and waterproof the roof penetration for shingle or flat rubber roofs. Available for flat roofs or pitched roofs, we offer them for 0/12 thru 6/12 and 7/12 thru 12/12 pitches. Constructed from Galvanized steel the flashing will tuck under the... Read More

From$519.31

The DuraTech Class A Square Cathedral Ceiling Support Box is used to support the DuraTech Class A Chimney Pipe when passing through a cathedral ceiling. The DuraTech Chimney Pipe twist-locks into the interior of the support box providing a positive connection to the chimney pipe. The support boxes are available... Read More

From$217.94

The DuraTech Class A Tee Support is used to support the Class A Tee connection (sold separately) to carry the weight of the vertical chimney pipe outside. The Class A Tee Support will mount directly to the side of the building underneath the wall thimble. The tee connection will sit in... Read More

From$215.87

The DuraTech Class A Wall Thimble is used to allow safe passage of the DuraTech Class A chimney pipe when passing through a combustible wall. The Wall Thimble can adjust from 4" to 10" to accommodate varying wall thickness. The interior firestop is painted black with a galvanized exterior firestop.... Read More

From$690.48

The DuraTech Class A Elbow Kit allows you to offset the pipe when there is an obstruction in the chimney pipes path. Oftentimes when installing an appliance, the appliance needs to be in a very specific location. The location of the vent is not always going to line up perfectly... Read More

From$207.68

The DuraTech Extended Wall Support Bracket is used to support the pipe off the side of the home when bypassing obstructions or roof overhangs. Typically used for through the wall venting. The Extended Wall Support Bracket can be used in place of the Tee Support and is capable of supporting... Read More

From$89.81

The DuraTech Wall Strap is used for interior and exterior installations to provide lateral support for the chimney pipe. The Wall Strap is required every 8 ft. above either the tee support for through the wall installation and the ceiling box for a through the ceiling or inside a chase... Read More

From$156.49

The DuraTech Chimney Cap easily attaches to the top of the DuraTech chimney pipe and is used to prevent weather or animals from entering the Class A chimney pipe. The cap is also equipped with a 1" spark arrestor that will help to prevent any hot embers from exiting the... Read More

$33.39

Add the DuraTech Spark Arrestor to your DuraTech Chimney Cap to have a smaller 1/2" mesh on the chimney cap. The finer mesh will prevent larger embers from leaving the chimney which helps prevent against wild fires. In some areas and jurisdictions a 1/2" mesh Spark Arrestor is required. The... Read More

From$27.49

The DuraTech Storm Collar is used to seal the gap between where the pipe comes through the roof flashing or a chimney chase cover. The Storm Collar wraps around the pipe tightly to shed the rain and snow away from the pipe. Once the Storm Collar is around the pipe... Read More

From$140.33

The DuraTech Roof Support is used when the pipe is passing through a ceiling and a roof to support the weight of the pipe. Typically used for cathedral ceiling installation it allows the pipe to extend below the ceiling while sitting on the roof joist. The Roof Support has adjustable... Read More

From$145.30

The DuraTech Firestop Joist Shield is used when the DuraTech Class A pipe is passing through a floor or ceiling where a ceiling support box is not used. The plate gets mounted to the underside of the ceiling and the sleeve is adjustable to cover the framing. Note: The Firestop... Read More

From$197.06

The DuraTech Extended Roof Bracket is used to stabilize the DuraTech chimney pipe above the roof when the pipe is extending 5 ft. or higher above the roof. The Extended Roof Bracket will clamp around the chimney pipe and has two adjustable length steel poles that mount to the roof... Read More

From$142.01

The DuraTech Attic Insulation Shield is used when the pipe is going through a ceiling into an attic space to prevent anything from coming in contact with the Class A pipe. This prevents any debris or insulation from getting into the ceiling support box. The Attic Insulation Shield consists of... Read More

From$129.53

The DuraTech Finish Collar is used to make the transition from the DuraTech Class A chimney pipe to single wall stove pipe for through the wall applications and when the chimney pipe is suspended with a roof support system. The DuraTech Finish Collar simply twists into the male end of... Read More

From$118.81

The DuraTech Class A Anchor Plate is used when connecting DuraTech chimney pipe to either a prefab zero clearance or a masonry fireplace. The Anchor Plate is the starter section that will mount directly to the exhaust hole of the fireplace and transition to the DuraTech Chimney Pipe. Once the... Read More

From$129.40

The DuraTech Single Wall Snap Lock Adapter with Trim is used to make the connection from a DuraTech Ceiling Support Box to single wall black stove pipe. The Snap Lock Adapter simply snaps to the bottom of the ceiling support box and provides a positive drip free connection from the... Read More

From$18.82

The DuraTech Locking Band is used for extra support and security when using offset elbows or horizontally venting the pipe connection at the tee. The Locking Bands are not required for the vertical pipe section. However, they will prevent the pipe from potentially twisting off during cleanings or inspections. Measurement... Read More

From$430.84

The DuraTech Telescoping Chimney Pipe is capable of adjusting from 14" to 21". This can be extremely helpful when you need a certain section of chimney pipe in between offsetting elbows or when a very specific length of pipe is needed through the wall thimble. Since the class A chimney... Read More